WARNING  - THIS ACCESSORY IS NOT MEANT TO BE USED UNDERWATER AS PER MANUFACTURER INSTRUCTIONS! ANY ATTEMPT TO DO SO CAN CAUSE EQUIPMENT LOSS AND IS NOT COVERED BY THE WARRANTY!

Compatible models:

SeaFrogs Underwater camera housing for Sony A6600 collection

SeaFrogs Underwater camera housing for Sony A6700 collection

SeaFrogs Underwater camera housing for Sony ZV-E10 collection

SeaFrogs Underwater camera housing for Sony ZV-E1 collection

SeaFrogs Underwater camera housing for Sony A1 collection

SeaFrogs Underwater camera housing for Sony A7C collection

SeaFrogs Underwater camera housing for Sony A7C II collection

SeaFrogs Underwater camera housing  for Sony A7 II NG collection

SeaFrogs Underwater camera housing for Sony A7 III collection

SeaFrogs Underwater camera housing for Sony A7R III collection

SeaFrogs Underwater camera housing for Sony A7 IV NG collection

SeaFrogs Underwater camera housing for Sony A7R IV collection

SeaFrogs Underwater camera housing for Sony A7R V collection

SeaFrogs Underwater camera housing for Sony A9 collection

SeaFrogs Underwater camera housing for Sony A9 II collection

SeaFrogs Underwater camera housing for Sony  FX3 collection

SeaFrogs Underwater camera housing for Sony FX30 collection

SeaFrogs Underwater camera housing for Sony A7S III Salted Line collection

SeaFrogs Underwater camera housing for Sony A7 IV Salted Line collection

Sony A6xxx series Salted Line 60M/195FT Underwater camera housing

Sony RX1xx series Salted Line 60M/195FT Underwater camera housing

Panasonic Lumix GH5 & GH5 S 40m/130ft Underwater Camera Housing

Olympus E-M5 III 40M/130FT Underwater camera housing

Olympus TG-5 & TG-6 60m/195ft SeaFrogs Underwater Camera Housing

Fujifilm X-H2 40M/130FT Underwater camera housing

Fujifilm X-S20 40M/130FT Underwater camera housing

Fujifilm X-T5 40M/130FT Underwater camera housing

Fujifilm X-T4 40M/130FT Underwater camera housing

Fujifilm X-T2 40M/130FT Underwater camera housing

(units that are sold from 1st of May 2019)

Fujifilm X-T3 40M/130FT Underwater camera housing

Fujifilm X-T30 40m/130ft SeaFrogs Underwater Camera Housing

Canon G1X III 40m/130ft SeaFrogs Underwater Camera Housing

Canon EOS M50 40m/130ft SeaFrogs Underwater Camera Housing

Canon EOS M6 Mark II Waterproof camera housing

Canon EOS RP Waterproof camera housing

Canon EOS R5 Waterproof camera housing

Canon EOS R6 Waterproof camera housing

Canon EOS R6 II Waterproof camera housing

Included:

• Electronic valve
• Pump
• Screwdriver (for battery replacement)

The vacuum pump system is used for checking the water tightness of underwater camera housing before submerging.
Install the camera inside underwater camera housing in dry and low humidity level place.

15-30 minutes before your dive remove the lid from backplate to access vacuum pump system opening (Illustration 1) and make sure the O-ring stays in place. Attach the vacuum pump system to the opening by screwing it clockwise (Illustration 2). Unscrew the lid of an electronic valve (Illustration 3) and press the button to turn on the LED inside the valve (Illustration 4). Attach the rubber part of a pump to the valve and start pumping air out (Illustration 5). Red LED starts blinking, indicating ambient atmospheric pressure. The hand pump is fitted to the threaded valve body and the air is pumped out of a unit until the red LED changes to green LED and add couple more strokes to make sure the sufficient underpressure. The additional stroke or two ensures that the valve is not on the edge of the threshold. The pump is then removed, and the protective cap replaced to ensure airtightness. Observe the green LED blinking for 15 minutes to make sure there is no air leakage. Unscrew the lid of a valve to access the button and press it for a few seconds to release the pressure from inside and turn the valve LED off (Illustration 4). Remove the valve from backplate and place vacuum opening lid to its original place, make sure the O-ring is still there (Illustration 1). - safe to dive!